Gadget Site
Uttam Electronics (Automation)
(A TRUSTED NAME IN PLANT AUTOMATION)

Level controller

These are suitable for conductive liquids like water and for non-conductive liquids like Diesel/Oil. Models for either one level monitoring or two level monitoring. 
Can be used for potable water, water with impurities and for diesel/oil
Cable size & length no restriction for water level monitoring
Suitable for variety of electrodes
Optical sensing for diesel/oil level monitoring
Open collector output (for FRKP4)
Choice of enclosures (DIN-Rail, & Plug-in)
Use of SMD Technology (S2 Series models)

Level Switch

Designed as per the set industrial standards, our assortment of Level Switches is highly acclaimed amidst the nationwide clients. We are renowned as one of the prominent Level Switches Suppliers, based in New Delhi (India). The Level Switches can be availed from us at the market leading prices.


Types Of Level Switches

RTD PT-100

platinum resistance temperature detector (RTD) Pt100 is a device with a typical resistance of 100 Ω at 0°C (it is called Pt100). It changes resistance value as its temperature changes following a positive slope (resistance increases when temperature is increasing).

They have been used for many years to measure temperature in laboratory and industrial processes, and have developed a reputation for accuracy,repeatability, and stability. A RTD can typically measure temperatures up to 850 °C. The relationship between resistance and temperature is relatively linear as shown below for a sample 100 Ω.

Level Sensor

Wide spectrum of sensors is available in the market and commonly, they are classified based on the specific application of the sensor. Sensor used for measuring humidity is termed as humidity sensor, the one used for measurement of pressure is called pressure sensor, sensor used for measurement of displacement is called position sensor and so on though all of them may be using the similar sensing principle. In a similar fashion, the sensor used for measurement of fluid levels is called a level sensor.

Quite obvious from its name, level sensors are used to measure the level of the free-flowing substances. Such substances include liquids like water, oil, slurries, etc as well as solids in granular/powder form (solids which can flow). These substances tend to get settled in the container tanks due to gravity and maintain their level in rest state. Level sensors measure their level against a pre-set reference.

 

Multi Channel Data Logger

 A data logger is any device that can be used to store data. This includes many data acquisition devices such as plug-in boards or serial communication systems which use a computer as a real time data recording system. However, most instrument manufacturers consider a data logger a stand alone device that can read various types of electrical signals and store the data in internal memory for later download to a computer.
The advantage of data loggers is that they can operate independently of a computer, unlike many other types of data acquisition devices. Data loggers are available in various shapes and sizes. The range includes simple economical single channel fixed function loggers to more powerful programmable devices capable of handling hundreds of inputs. 

Float type level Sensor

Level sensors allow for the level control of fluid in a vessel. Examples of where these sensors are installed include reactors, distillation columns, evaporators, mixing tanks, etc. Level sensors provide operators with three important data for control: The amount of materials available for processing, The amount of products in storage, The operating condition. Installing the correct level sensor ensures the safety of the operator and the surrounding environment by preventing materials in vessels from overflowing or running dry.

Multi level sensor

Designing you own tank level sensor or pump control can be easy.  We can design a tank level sensor to indicate your tank levels or to maintain the level of your fluid in a tank or vessel.   If you need Level/Temperature, Oil/Water interface or if you just want help designing your own custom tank level sensor.

Temperature Indicator

A time temperature indicator is a device or smart level that shows the accumulated time-temperature history of a product. Time temperature indicators are commonly used on food, pharmaceutical and medical products to indicate exposure to excessive temperature (and time at temperature).

PID Controller

 A proportional- integral - derivative controller (PID Controller) is a generic control loop feedback mechanism (controller) widely used in industrial control systems. A PID controller calculates an "error" value as the difference between a measured process variable and a desired set point. The controller attempts to minimize the error by adjusting the process control units.

Conductivity Transmitter

We are renowned as one of the prominent Level Transmitters Manufacturers and Suppliers, based in India. The Level Transmitters, that we provide, are known for their excellent efficiency and longer working life. The Level Transmitters are available with us in a wide range that is designed as per the set industrial standards.


Types Of Level Transmitters

 

Flow Meter

The company is engaged in the manufacturing and supplying of Flow Transmitter all across the country. The Flow Transmitter, which we offer, is available in a wide range in order to meet the specific needs of diverse industries. Our Flow Transmitters are designed in compliance with the set industrial standards to ensure their reliability and superb efficiency.


Range Of Flow Transmitters

 

Level Controller


 Level sensors detect the level of substances that flow, including liquids, slurries, granular materials, and powders. Fluids and fluidized solids flow to become essentially level in their containers (or other physical boundaries) because of gravity whereas most bulk solids pile at an angle of repose to a peak. The substance to be measured can be inside a container or can be in its natural form (e.g., a river or a lake). The level measurement can be either continuous or point values. Continuous level sensors measure level within a specified range and determine the exact amount of substance in a certain place, while point-level sensors only indicate whether the substance is above or below the sensing point. Generally the latter detect levels that are excessively high or low.

Pneumatically Actuated Valve

A pneumatic actuator converts energy (typically in the form of compressed air) into mechanical motion. The motion can be rotary or linear, depending on the type of actuator. A Pneumatic actuator mainly consists of a piston, a cylinder, and valves or ports. The piston is covered by a diaphragm, or seal, which keeps the air in the upper portion of the cylinder, allowing air pressure to force the diaphragm downward, moving the piston underneath, which in turn moves the valve stem, which is linked to the internal parts of the actuator.

Control Valve

Control valves are valves used to control conditions such as flow, pressure, temperature, and liquid level by fully or partially opening or closing in response to signals received from controllers that compare a “set-point” to a “process variable” whose value is provided by sensors that monitor changes in such conditions.

The opening or closing of control valves is usually done automatically by electrical, hydraulic or pneumatic  actuators. Positioners are used to control the opening or closing of the actuator based on electric, or pneumatic signals. These control signals, traditionally based on 3-15 psi (0.2-0.1 bar), more common now are 4-20mA signals for industry, 0-10V for HVAC systems, and the introduction of “smart” systems, HART, Fieldbus Foundation, and Profibus being the more common protocols.

Electrical Panel

A control panel is a flat, often vertical, area where control or monitoring instruments are displayed. They are found in factories to monitor and control machines or production lines and places such as power plants, ships, aircraft and mainframe computers. Older control panels are most often equipped with push buttons and analog instruments, where as today in many cases touch screens are used for monitoring and control purposes.

SMPS

A switched-mode power supply (switching-mode power supply, SMPS or switcher) is an electronic power supply that incorporates a switching regulator to convert electrical power efficiently. Like other power supplies, an SMPS transfers power from a source, like mains power, to a load, such as a personal computer, while converting voltage and current characteristics. Unlike a linear power supply, the pass transistor of a switching-mode supply continually switches between low-dissipation, full-on and full-off states, and spends very little time in the high dissipation transitions, which minimizes wasted energy. Ideally, a switched-mode power supply dissipates no power, Voltage regulation is achieved by varying the ration of on-to-off time. In contrast, a linear power supply regulates the output voltage by continually dissipating power in the pass transistor. The higher power conversion efficiency is an important advantages of a switched-mode power supply. 

Solenoid Valve

A solenoid valve is an electomechanically operated valve. The valve is controlled by an electric current through a solenoid: In the case of a two-port valve the flow is switched on or off, in the case of a three-port valve, the outflow is switched between the two outlet ports. Multiple solenoid valves can be placed together on a manifold.

CIP Plant

Cleaning-In-Place (CIP) is system designed for automatic cleaning and disinfecting without major dis assembly and assembly work. Additionally, a well designed CIP system (employing double seat valve (block and bleed) technology and a bit of process integration) will enable you to clean one part of the plant while other areas continue to produce product. Furthermore, a modern CIP system will not only save money in terms of higher plant utilization but also due to significant savings in CIP liquid (by recycling cleaning solutions), water (the system is designed to use the optimum quantity of water)

FDV

Display Board

Display board (ss 304) for temperature / quantity or level / pressure etc..Number of channels as per requirment

pneumatic control valve

pneumatic control valves with or without electro pneumatic positioner make samson size 1" to 6"

Heat blower

Heat blower in ss body with electric static heaters, exhaust fan and flow switch for interlocking of heaters for incubator rooms , dahi room etc..

CIP PANEL

Desk type ss panel for cip with instrument (digital temperature indicator,controller,pid controller,warning light with hooter,indications,push button,selector switches,relay cards,smps,plc,hmi,input output analog modules etc..) and mimic panel with indication for operation of cip.